- A+
本文描述了AP9617,AP9618,AP9619的设置步骤。
使用AP9617,AP9618,AP9619之前，必须设置一些基本参数。本文介绍了如何通过串口通讯方式配置AP9617，AP9618,AP9619. 配置步骤如下：
1．使用940-0024C通讯线（网络管理卡附带）连接运行终端仿真程序的计算机和UPS。
2．如该计算机的串口（连接940-0024C通讯线）正被APC软件PowerChute Plus或其他程序使用，请关闭相关程序。 启动终端仿真程序如HyperTerminal，设置串口参数为：2400bps, No Parity , 8 data bits , 1 stop bit , and No Flow Control
注：修改串口参数后，要断开并重新连接该会话(connection)之后，设置方生效。
3. 确认上述两步无误后，按回车键。
4. 输入 User Name及 Password ，其缺省设置均为 apc。
5. 正确登录后，网络管理卡的管理界面将自动弹出。
显示界面如下：（请根据您的需求修改相关参数）
User Name : apc
Password : ***
American Power Conversion Network Management Card AOS v2.1.1
(c) Copyright 2002 All Rights Reserved Smart-UPS & Matrix-UPS APP v2.1.0
-------------------------------------------------------------------------------
Name : Unknown Date : 12/11/2003
Contact : Unknown Time : 11:47:50
Location : Unknown User : Administrator
Up Time : 0 Days 0 Hours 20 Minutes Stat : P+ N? A+
Environment : Threshold Violation Present, Contact Alarms Disabled, Relay
Disabled
Smart-UPS 1000 named : On Line
------- Control Console -------------------------------------------------------
1- Device Manager
2- Network
3- System
4- Logout
<ESC>- Main Menu, <ENTER>- Refresh, <CTRL-L>- Event Log
> 2
------- Network ---------------------------------------------------------------
1- TCP/IP
2- DNS
3- Ping Utility
4- FTP Server
5- Telnet/SSH
6- Web/SSL/TLS
7- WAP
8- SNMP
9- Email
10- Syslog
<ESC>- Back, <ENTER>- Refresh, <CTRL-L>- Event Log
> 1
------- TCP/IP ----------------------------------------------------------------
Network not started. Currently making a BOOTP request...
-----------------------------------------------------------------------
MAC Address : 00 C0 B7 67 37 4C
1- Boot Mode : DHCP & BOOTP
2- Advanced...
<ESC>- Back, <ENTER>- Refresh, <CTRL-L>- Event Log
> 1
------- Boot Mode -------------------------------------------------------------
1- DHCP & BOOTP
2- DHCP only
3- BOOTP only
4- Manual
<ESC>- Back, <ENTER>- Refresh
> 4
------- TCP/IP ----------------------------------------------------------------
Network not started. Currently making a BOOTP request...
-----------------------------------------------------------------------
MAC Address : 00 C0 B7 67 37 4C
* Changes will take effect on Logout.
1- System IP : 159.215.125.248
2- Subnet Mask : 255.255.255.0
3- Default Gateway: 159.215.125.1
4- Boot Mode : Manual
5- Advanced...
<ESC>- Back, <ENTER>- Refresh, <CTRL-L>- Event Log
> 1
System IP : 159.215.125.248
------- TCP/IP ----------------------------------------------------------------
Network not started. Currently making a BOOTP request...
-----------------------------------------------------------------------
MAC Address : 00 C0 B7 67 37 4C
* Changes will take effect on Logout.
1- System IP : 159.215.125.248
2- Subnet Mask : 255.255.255.0
3- Default Gateway: 159.215.125.1
4- Boot Mode : Manual
5- Advanced...
<ESC>- Back, <ENTER>- Refresh, <CTRL-L>- Event Log
> 5
------- Advanced... -----------------------------------------------------------
Link is down.
1- Host Name : APC
2- Domain Name : somedomain.com
3- Port Speed : Auto-negotiation
4- Accept Changes:
<ESC>- Back, <ENTER>- Refresh, <CTRL-L>- Event Log
> 4
------- Advanced... -----------------------------------------------------------
Link is down.
1- Host Name : APC
2- Domain Name : somedomain.com
3- Port Speed : Auto-negotiation
4- Accept Changes: Success
<ESC>- Back, <ENTER>- Refresh, <CTRL-L>- Event Log
>
需要注意的是TCP/IP的三个参数包括System IP,Default Gateway,Subnet Mask都必须设置，尤其网关Default Gateway不能为0.0.0.0,否则会导致网络不通。退出超级终端，则网络设置成功。
首先用ping 命令检查网络配置是否成功，如果不能Ping通，请将卡Reset,卡上有一个白色的Reset按钮，按一下，则卡重启，该重启只是卡重新加电而已，不会改变卡内的已有的任何设置
UPS电源山特UPS四通艾默生山顿APC梅兰日兰
中国宏业电器经销各品牌排行UPS电源，购买UPS电源、了解各品牌UPS价格或索取各型号UPS技术参数资料请添加微信或者联系电话获取。
